To maintain a wet edge, start near a corner and run the roller up and down the full height of the wall, moving over slightly with each stroke. Move backward where necessary to even out thick spots or runs. Don’t let the roller become nearly dry; reload it often so that it’s always at least half loaded. Keep the open side of the roller frame facing the area that’s already painted. That puts less pressure on the open side of the roller, so you’re less likely to leave paint ridges when doing DIY wall painting.
When I had my interior painting done, after clearing out all of the furniture, myself, I also removed all of the wall plates in all the rooms to be painted. They were a beige color and probably yellowed. The wall was originally an off white and I had it painted a light-mid grey, so those wall plates would look terrible. After pricing replacement plates, switches and outlets (Would have been way too expensive to replace all of them), I decided to just paint all of the wall plates, switches and outlets (Used just a black gloss spray paint). I sprayed the plates outside and used a small brush on the switches and outlets. It worked out just fine and the blacks plates, etc compliment the wall color. It has been 7 years and the plates, switches, outlets are holding up well.
Modern Masters 1 gal. Antique Copper Metallic Interior Modern Masters 1 gal. Antique Copper Metallic Interior Paint can be used to create a high-end decorative finish in a variety of circumstances. Use it on a small accent piece or large architectural specification. Durable and long lasting for commercial application yet easy enough for do-it-yourself projects. Special formula contains ...  More + Product Details Close
Small random-orbit or pad sanders make this job go faster. (Wallis first covers these boundaries with Synkoloid patching compound so no edge is visible after sanding.) As shown, you want to make sure that there is a feathered, smooth transition from exposed wood to old paint. For areas that might get close scrutiny, you can follow up with a 100- or 120-grit rubdown to erase any scratches.
As a former professional painter, something that drives me crazy is when I see painters cut in around wall plates. First of all, the amount of time that it takes to cut in is usually much longer than the amount of time that it takes to simply remove the wall plate. Secondly it does not look nearly as clean as it does when the wall plate is removed and thirdly it can invariably leave paint on the wall plate itself which also looks sloppy. Make sure the painter takes them off and then reinstalls them. It's less time.
If you’re looking for information on a professional painting company in the Minneapolis/St. Paul metro, you’ve come to the right place. Providing the Twin Cities with durable, residential interior and exterior painting is the reason we’re here—and we go far beyond that valued service for our customers. The “Plus” in Durahome Painting Plus offers our talents, skills and high standards to take care of other home improvement projects as well. Just check out our list of Services to find those that might interest you.

O'Neil patches shallow holes and divots with Ready Patch because it dries fast, sands smooth, and stays flexible. Deep cracks and rotten spots are best repaired with two-step epoxies, such as those made by Advanced Repair Technology. (For a step-by-step instructions, see Repairing Rot with Epoxy.) The days of using polyester auto-body fillers on wood are over. "They cure too hard," says Portland, Oregon–based painting contractor Kathleen George. "They look good at first, but then they peel away."


When I had my interior painting done, after clearing out all of the furniture, myself, I also removed all of the wall plates in all the rooms to be painted. They were a beige color and probably yellowed. The wall was originally an off white and I had it painted a light-mid grey, so those wall plates would look terrible. After pricing replacement plates, switches and outlets (Would have been way too expensive to replace all of them), I decided to just paint all of the wall plates, switches and outlets (Used just a black gloss spray paint). I sprayed the plates outside and used a small brush on the switches and outlets. It worked out just fine and the blacks plates, etc compliment the wall color. It has been 7 years and the plates, switches, outlets are holding up well.

Home Painter Company

×