Inspect the surface area for holes, cracks or other problems and apply acrylic caulk to fill them in. Use a putty knife to smooth out the caulk and remove any excess to prevent bumps. For particularly thin or narrow crevices, you may have to use your finger to smooth out the caulk. Caulk contracts and shrinks, so apply a second layer once it's dried.
Deciding which paint to use has gotten much easier now that acrylic latexes have pushed oil-based paints almost to extinction. The acrylics offer superior performance (they don't harden with age, the way oils do, so they move and breathe without blistering), they don't mildew as readily, and they emit fewer VOCs, so they comply with new air-quality regulations. They also work over both oil- and water-based primers.
When I had my interior painting done, after clearing out all of the furniture, myself, I also removed all of the wall plates in all the rooms to be painted. They were a beige color and probably yellowed. The wall was originally an off white and I had it painted a light-mid grey, so those wall plates would look terrible. After pricing replacement plates, switches and outlets (Would have been way too expensive to replace all of them), I decided to just paint all of the wall plates, switches and outlets (Used just a black gloss spray paint). I sprayed the plates outside and used a small brush on the switches and outlets. It worked out just fine and the blacks plates, etc compliment the wall color. It has been 7 years and the plates, switches, outlets are holding up well.
O'Neil patches shallow holes and divots with Ready Patch because it dries fast, sands smooth, and stays flexible. Deep cracks and rotten spots are best repaired with two-step epoxies, such as those made by Advanced Repair Technology. (For a step-by-step instructions, see Repairing Rot with Epoxy.) The days of using polyester auto-body fillers on wood are over. "They cure too hard," says Portland, Oregon–based painting contractor Kathleen George. "They look good at first, but then they peel away."
Ask companies to include all details in writing. Although that sounds simple enough, too many contractors submit offers such as "paint house for $5,000." A friendly contractor may offer a reassuring handshake and promise that the crew will take care of all the details — starting on time, working every day, cleaning up, etc. That's great, but why not include each point in the proposal? If it's a challenge to get a written description of labor, materials and other details, things will probably get worse when the work starts.
I have a Home Improvement/Painting business, and Angie's List always advertises that that everyone is out to get them. Of course there are people who try to take advantage of homeowners My reputation and repeat business is based on word of mouth. Shoddy work is always a way to get put out of business quick. As far as strictly painting, preparation is a big factor in getting a quality paint job. If you don't prepare the surfaces you are painting you are spinning your wheels, and wasting money, no matter what paint you use. Getting a deposit from a customer is beneficial, but not always necessary. Sometimes it is a godsend, when you get stuck by the customer, which has happened to me more than once
The companies with the best paint products are Benjamin Moore, Dunn Edwards, Sherwin Williams, and Vista Paint. As a painter I don't recommend Berh from Home Depot as much because it's quality is just marketing. Flat paint has no sheen and it shows its true color, but is not easy to wash or clean. Satin, eggshell have low sheen and is washable. Semigloss ang glossy has a high sheen and these paints are recommended for bathrooms and kitchen or where there's high humidity and steam.
The materials of the home’s facade should be considered before painting your home. When painting flat surfaces like siding or wood, you can opt for standard outdoor paint. When painting a textured surface like stucco or brick, “elastomeric” paint is a much better choice. This type of paint can stretch more than normal paint, which allows it to bridge over small gaps and crevices, painting smoothly over texture.

The only time it's acceptable to mix water in the paint is when you're using a deep or ultra deep base paint to reduce its stickiness, which is rare with new paint technology. Dark primary colors are composed almost entirely of tint that makes it very hard to work with without adding water. (You never use a sprayer and need to thin paint.?) If i was still in the industry I'd take the time to make a better article than this. Take this for a grain of slat. Use a reputable painter or someone you know you can trust or has been referred to you by someone you trust. I wouldn't hire anyone I had to watch like a hawk to make sure they're not screwing me.


I used to work at Sherwin Williams. The best thing to do is specify that you will purchase your own paint. If the painter objects strenuously, he was plaanning on making money in the ways this article outlines. You might pay a few dollars more for paint, but you will have control of the quality of what goes on your walls. Never skimp on paint quality.
I used to work at Sherwin Williams. The best thing to do is specify that you will purchase your own paint. If the painter objects strenuously, he was plaanning on making money in the ways this article outlines. You might pay a few dollars more for paint, but you will have control of the quality of what goes on your walls. Never skimp on paint quality.

Home Painters

×