Hi Donnie, Thanks for your comment! We would be happy to help you connect with a fencing pro to give you an estimate on your project. You can submit a request to our pros here: www.homeadvisor.com, browse a list of local pros here: http://www.homeadvisor.com/c.html, or send your info to [email protected] and a project advisor will reach out to assist you. –HASupport
I was taught to paint by a professional and when estimating the amount of paint needed, I always allow for a second coat just to make sure of coverage. We interviewed a painter who tried to tell me I bought poor quality paint without knowing where I purchased it, and stated he would have to buy all new paint. He had not seen the cans and was just guessing so I asked him where I should buy paint from now on. It was the same place I had purchased my paint and he wanted to charge me an extra 20 a gallon more than what I paid for. Needless to say, I have interviewed numerous painters and they are not all honest.
• One room or the whole house? Applying one coat in one room is a reasonable DIY Saturday project (especially if you have help and beer). Multiply the time spent moving furniture, prepping walls and sanding old trim by the number of rooms in the house, and you might want to hire real help. It's the same outside. You can probably tackle one shady garage wall that needs a little scraping and sanding plus a coat of paint, but covering all surfaces of the house is usually best left to a pro.
Freshly painted walls often look blotchy. The color is uniform, but the sheen isn’t consistent. This usually occurs over the holes and cracks you patched with a filler or drywall compound. The porous fillers absorb the paint, dulling the surface (a problem called “flashing”). When light hits these dull spots, they stick out like a sore thumb. The smooth patch also stands out in contrast to the slightly bumpy texture of the rest of the wall. A quick coat of primer is all it takes to eliminate ﬂashing and texture differences.
Next, undercut the trim to create a gap (Photo 3). When you’re done, scrape any dirt or gunk out of the gap with a putty knife and blow out the dust using a vacuum or air compressor. To avoid staining the concrete, run at least three layers of masking tape under the wood. Apply repellent to all bare wood (Photo 4) including the underside (Photo 5). Bend a putty knife in a vise to make a handy tool for reaching into tight areas. Remove the tape right after application.
For interior paint I prefer the semi-gloss, provides a very subtle sheen and is super easy to clean -no flaking, chipping, etc. I've painted a lot, and found that Sherwin Williams Ovation paint has been the easiest to use, and provides the best coverage. I even painted my ceilings with it and WOW! I was done it no time at all, with perfect coverage.
Excellent advice because there are many unskilled workers who are "trying to pull the wool over the customers eyes". One has to study about the project for which they are in need. I happen to need dry wall repair and painting done in my home and feel the advice in this article will be a great help to me in hiring someone who is ethical and does good work. Thanks.
When the primer is dry, caulk all small joints (less than ¼-inch-wide) in the siding and trim. Most pros use siliconized acrylics—paint won't stick to straight silicones—but Guertin and O'Neil like the new, more expensive urethane acrylics for their greater flexibility and longevity. O'Neil stresses that it's shortsighted to skimp on caulk. "If the joint fails, you're back to square one." Guertin uses the lifetime rating as his quality guide. "I don't expect 35-year caulk will last 35 years, but it should last longer than a 15-year caulk."
To get at the nails in the board above, shove a flat pry bar up under it and gently pry the board outward. In most cases, this will pop up the nailhead, so you can pull it with your hammer claw. If you run into a stubborn nail that won’t move easily, don’t use brute force and risk splitting the good board. Instead, slip a hacksaw blade behind the siding and cut the nail (Photo 2).You can’t get the new board in unless you pull the remaining shank of the cut nail (Photo 3).
my grandfather was a painter and he taught me the importance of quality workmanship and it shows in every job I do my customers are happy with a beautiful job every time. I thoroughly enjoy the work that I do and your satisfaction is very important to me. If a neat and clean quality paint job is what you're looking for then I am definitely your guy ,thanks !
Our consultation process is easy, informative, specific to your project and headache-free. With all the colors, shades, tones, and tints to choose from these days, it can be overwhelming to choose just the right color for your home. 360° Painting Cleveland can help you to get assistance from a professional in-home color consultant to determine the colors that would look best in your home and fit your décor or objectives. Once you’ve narrowed down the color group, you can test your final color selection by using one of the following options:
When I had my interior painting done, after clearing out all of the furniture, myself, I also removed all of the wall plates in all the rooms to be painted. They were a beige color and probably yellowed. The wall was originally an off white and I had it painted a light-mid grey, so those wall plates would look terrible. After pricing replacement plates, switches and outlets (Would have been way too expensive to replace all of them), I decided to just paint all of the wall plates, switches and outlets (Used just a black gloss spray paint). I sprayed the plates outside and used a small brush on the switches and outlets. It worked out just fine and the blacks plates, etc compliment the wall color. It has been 7 years and the plates, switches, outlets are holding up well.